Skip to main content

Spiral finned tube

Spiral finned tube (also known as finned tube, finned tube welding equipment performance and parameters of fin tube main performance indicators are shown in the table, the products comply with HG/T3181 the high-frequency resistance welding of spiral fin tube "and JB/T6512" boiler with high frequency resistance welding of spiral fin tube manufacturing technical conditions "requirement.

The performance parameters of the welding equipment of the spiral finned tube

Welding power source (W) 300

Maximum spindle speed (RPM) 300

The welding pipe diameter (mm) ~ Phi Phi 25 168

Thickness of welded steel pipe (mm) 2 to 10

Length of welded steel pipe (m) 0.5 to 25

The width of the welded fin (mm) 13 to 30

Thickness of the welded fin (mm) 0.8 to 2.5

Fin pitch (mm) 4 to 90

Open tooth pitch (mm) 4.5 ~ 8

Weld line speed (m/min) 35

Spiral to the left and right.

Welding material carbon steel, low carbon steel, stainless steel

Main performance index of fin tube

The fin height deviation less than 0.75mm

The fin pitch deviation in any 10 pitch and the average of less than 0.2mm

Straightness per meter of finned tube length is less than or equal to 1mm, less than 10mm

Fin and tube surface verticality (fin tilt angle alpha = 8 DEG)

(measured at the actual weld length of sum and the measurement theory of weld length) La is more than or equal to 0.95Lt fin and pipe surface longitudinal welding rate

Fin and tube surface transverse welding rate (compared with the sum of the average width of strip thickness measurement at the actual weld) Sa = 0.85Sf

The welding specimen tensile strength more than 200MPa

Spiral finned tube



Comments

Post a Comment

Popular posts from this blog

What are the components of finned tube bundle?

The heat exchange unit composed of multiple finned tubes arranged according to certain rules is called finned tube bundle. A finned tube heat exchanger can be composed of one or more finned tube bundles. Understanding the finned tube bundles is helpful to the application of finned tube heat exchangers.   What are the components of finned tube bundle?   1. Multiple finned tubes: basic elements of heat transfer;   2. Tube box header or tube plate: connect the box, elbow or steel plate at both ends of the finned tube. When the finned tube is connected with the box or tube plate, the spacing between the finned tubes is fixed, and the tube box makes the fluid in the tube form a continuous flow channel;   3. Frame: support and fix the whole finned tube bundle.   The finned tube bundle is the main part of the air cooler, which is composed of finned tubes, tube boxes and frames. It is an independent structural whole. Its basic parameters include the tube bundle type (us...
Post a Comment
Read more

ASTM A213 T22 extruded finned tube?

  What is ASTM A213 T22 extruded finned tube? ASTM A213 T22 extruded finned tube is a heat exchanger tube with extruded aluminum fins on the outside surface, made from T22 grade steel, which is an alloy steel per ASTM A213 standard. The fins are extruded from the base tube, which increases the surface area and enhances heat transfer efficiency. These finned tubes are typically used in high-temperature and high-pressure applications, such as boilers, superheaters, and heat exchangers in power plants or industrial settings. The T22 grade steel has good high-temperature strength and resistance to corrosion and oxidation. Why use ASTM A213 T22 extruded finned tube? ASTM A213 T22  extruded finned tubes  are used in applications where high-temperature and high-pressure resistance is required, such as in boilers and heat exchangers. The use of an extruded finned tube made of this material can improve the heat transfer rate by increasing the surface area of the tube, which enhanc...
Post a Comment
Read more

H-shaped finned tube or square finned tube advantages

H-shaped finned tube or square finned tube advantages: H-shaped finned tube or square finned tube adopts a new welding process. A number of zigzag structures are used at the welding contact parts of the fins, so that the heating is uniform, the welding surface is uniform, and the surface is smooth. There is no slag inclusion, porosity and weld beading. The welding fusion rate is up to 97%. Due to the uniform heating, the compression plastic deformation generated in the welding process is reduced, the longitudinal residual tensile stress near the weld is reduced and the residual compressive stress borne by the fin far from the weld is greatly reduced, which can significantly reduce the wave deformation of the fin and make the welding quality of H-shaped fin tube meet the requirements of technical conditions. H Shape Finned Tube Typical Material and Size H Shape Finned Tube Base Tube Size φ 32*4 φ32*5 φ38*4 φ38*5 φ42*5 φ48*5 φ51*5 φ51*6 H Shape Finned Tube Fin Size 70mmX70mm 、 75mmX75mm...
Post a Comment
Read more