High Frequency Finned Tubes Solid/Serrated

High Frequency Finned Tubes: The steel fin, that may be solid or serrated, is helically wound and continuously welded to the tube by high frequency electric resistance welding. This produces an homogeneous, clean and continuous fin-totube bond with no additional weld material, for a very efficient heat flow and resistance to corrosion.

There are some applications for which one or the other fin type is preferred. While in some cases fouling and cleaning considerations will favour solid fins, serrated fins are superior with respect to weight, compactness and price.

The use of high-frequency current results in very localised heating of the tube surface and the edge of the fin. This skin effect produces higher weld speeds, hence post-weld heat treatment is not considered necessary because of the superficial nature of the changes in the microstructure.

High Frequency Finned Tubes bending:

Our finning machines are equipped with online single or duplex cold bending equipment that can manipulate both ends of tubes in a single operation, thus ensuring exact alignment of the ends. Our bending machines are capable of bending both bare or finned tubes with diameters from 31 mm to 76 mm.

High Frequency Finned Tubes Corrosion protection:

If required, the external surfaces of finned tubes can be treated with a protective coating. Our engineers are always ready to assist you with design considerations to meet your specific product needs.

Comments

What is tube sheet layout?

What is tube sheet layout? A tube sheet is a component used in shell and tube heat exchangers and other types of heat transfer equipment. It is a flat plate with holes drilled in it, through which tubes are inserted and secured. The tube sheet serves as a barrier between the two fluids, allowing heat to be transferred from one to the other. The layout of the tube sheet depends on the design of the heat exchanger, which includes the number of tubes, the size of the tubes, and the spacing between the tubes. The layout is typically determined using computer-aided design (CAD) software, which can optimize the placement of the tubes to achieve the desired heat transfer performance. In general, the tubes are arranged in a triangular or square pattern on the tube sheet. The triangular pattern is often preferred because it provides better support for the tubes and reduces the risk of vibration and damage. The spacing between the tubes is also important, as it affects the flow rate and pressure...

What is aluminum finned tubes?

What is aluminum finned tubes? Aluminum finned tubes are a type of finned tube air heat exchanger that uses aluminum fins attached to a tube made of a different material, such as copper or steel. The aluminum fins are typically extruded or formed to increase the surface area of the tube, which in turn increases the efficiency of heat transfer. Aluminum finned tubes are commonly used in HVAC systems, as well as in industrial and power plant applications. They are preferred over other types of finned tubes in some applications because they are lightweight, corrosion-resistant, and have good thermal conductivity. Additionally, aluminum is relatively inexpensive compared to other metals commonly used in heat exchangers, such as copper and stainless steel. The specific properties of aluminum finned tubes can vary depending on the alloy used to make the fins. For example, aluminum fins made from alloys such as 6061 and 3003 have good corrosion resistance and thermal conductivity, while those...

What is the difference between pipe bends and elbows?

Bends and elbows are fittings used to change the direction of a pipe. These two kinds of pipe fittings have a wide range of applications in construction, but in actual use, the performance of pipe bends and elbows is different, and elbows are used much more than pipe bends. What is the difference between pipe bends and elbows? An elbow is a pipe part with a bend, which is a commonly used pipe part. Bends are usually manufactured to specific needs. Compared with the elbow, the elbow is much longer and is a curved pipe, while the elbow is only a part that changes the direction of the pipe. Although both are components that change the direction of the pipeline, there are many differences between these two components. 1. Different manufacturing processes for pipe bends and elbows In the manufacturing process cold and hot bent pipes can be made of pipe bends, which directly bent by the pipe bending machine, and the bent pipe can be manufactured at one time without secondary...

Lord Fin Tube--T.S. Industrial Co.,Ltd

Search This Blog